Braemar Ducted Gas Heaters – 2026 Sales Options and Technical Product Guide


Overview

This article is a sales and dealer reference to help select the correct kits when quoting and ordering Braemar TQR Series ducted gas heaters.
It focuses on what dealers need to know at point of sale:
  • Which installation, controller, zoning, plenum and flashing kits apply to each heater
  • How installation type and system options affect kit compatibility
  • Where to find the relevant sections in the 2026 Heater Booklet for confirmation
Technical information is included only to support kit compatibility checks and should not be used in place of installer or commissioning manuals.
Source: 2026 Braemar Heating Product Guide – Electronic Edition


103-page Pdf including bookmarks attached

Ducted Gas Heater – Sales & Dealer Quick Guide

What This Guide Is For

This guide helps Sales teams and Dealers quickly select the correct heater kits, controllers, and zoning options when quoting or ordering Braemar ducted gas heaters.

Use it to avoid:

  • Wrong kits being ordered
  • Site re‑visits and delays
  • Controllers or zoning that won’t work together

How to Use This Guide (Sales Order Workflow)

When preparing an order:

  1. Confirm the heater model and star rating
  2. Confirm the install location
    (internal / external / under‑floor)
  3. Choose the correct MagIQtouch controller
    (wired, wireless, or Wi‑Fi)
  4. Check zoning needs
    (number of zones and 24V vs 240V)
  5. Confirm safety requirements

✅ Following this order prevents compatibility and installation issues.

Supported Heater Ranges

✅ Current 2026

  • TQR / TQRD Series
  • MagIQtouch controllers and zoning supported

⚠️ Discontinued (Service & Parts Only)

  • TQ / TQM / TQS / BMQ / CQB / CQS series
  • WF30/WF40, WF25, SH18, SH25 wall furnaces

➡️ Always confirm the exact model before ordering kits or parts.

Key Specs (Quick Check)

Gas Types

  • Natural Gas (NG) – approx. 1.13 kPa
  • ULPG / Propane – approx. 2.75 kPa

Heater Operation

Heater operation depends on the gas valve type, which can vary within the same heater family (including TQR).

✔ Single‑Stage

  • One fixed heat output 
  • Found on:
    • TQR 3‑star non-condensing - Metal fluing

✔ Two‑Stage

  • Low and high heat output
  • Found on:
    • TQR 4-star non-condensing - Metal fluing

✔ Modulating

  • Continuously varies heat output to match demand
  • Found on:
    • TQR 5-star non-condensing - Metal fluing
    • TQR 6-star condensing - PVC fluing 

Installation Basics (What Impacts Kit Choice)

  • Install kit must match:
    • Internal
    • External
    • Under‑floor
  • Correct flue and roof flashing required
  • Adequate return air relief required

Extra Air (“X”) Models

  • Required if adding cooling

Sales Kits Explained (2026 Heater Booklet)

Installation Kits (Pages 30–36)

Choose based on heater location:

  • Internal
  • External
  • Under‑floor
    Includes flue parts and mounting hardware.

MagIQtouch Controller Kits (Pages 24–25, 29)

  • Wired
  • Wireless (RF – blue label only)
  • Wi‑Fi‑enabled

Zone Control Kits (Pages 26–27)

  • 24V Zones – up to 10 zones
  • 240V Zones 

Always match:

  • Heater type
  • Number of zones
  • Damper voltage

Plenum / Down‑Flow Kits (Page 23)

Used when:

  • Replacing older Down discharge heaters

Flashing & Flue Guard Kits (Pages 40–43)

Used for:

  • External installs
  • Roof penetrations
  • Clearance and weather protection

? Sales Tip:
If a kit isn’t listed in the sales booklet, check whether it’s service‑only or obsolete before quoting.


Zoning Rules

24V Zoning

  • Up to 10 zones (depending on enclosures)

240V Zoning

  • ❌ Not allowed on SSQ models

➡️ Wrong zoning choice = rework and delays.


✅ Bottom Line for Sales

If you:

  • Confirm the model
  • Match the install type
  • Pick the right controller
  • Select the correct zone kit

➡️ You’ll avoid failed installs, returns, and warranty problems.