KDHA Wi-Fi Setup – EWPE App Connection (XE7C‑24/HC & LE60 Zone Control)

⚠️ Safety Notice – Reverse Cycle Air Conditioners

This equipment must only be installed, commissioned, serviced and repaired by suitably qualified and licensed personnel.


Before commencing work, complete a task-specific risk assessment and ensure electrical isolation procedures, safe access, adequate service clearances and appropriate PPE have been considered. All work must comply with applicable regulations, standards and manufacturer requirements.


Particular care must be taken when working around electrical systems, refrigerant circuits, moving parts, roof spaces, ceiling spaces, confined spaces and working-at-heights hazards where applicable.


Do not proceed if safe access, required clearances, confined space risks or appropriate safety controls cannot be achieved and maintained. 


Safety takes priority over diagnosis, repairs, installation schedules and customer expectations. If the task cannot be completed safely, it must not proceed until the risks have been adequately controlled.


Purpose

This article explains what hardware is required and how to configure the EWPE (Ewpe Smart) Wi‑Fi App for Braemar KDHA ducted systems, using either:
  • XE7C‑24/HC standard supplied wired wall controller (Wi‑Fi built in), or
  • LE60‑13/GH‑B Zone Control kit using the ME31‑00/C13 Wi‑Fi module

Manual References 

Use the following official documents when configuring EWPE Wi-Fi setup for KDHA systems:

KDHA Owner's Manual – XE7C-24/HC Wired Controller (supplied standard)

  • Wi-Fi Setup & App Connection: Pages 25-26
  • Reset Wi-Fi / Pairing Procedure: Page 26
  • EWPE (Ewpe Smart) App Download & Requirements: Page 25

Braemar LE60 Zone Control Installation Manual

  • Wi-Fi Module Overview (ME31-00/C13): Page 11
  • Wi-Fi Module Physical Installation: Page 11
  • EWPE App Commissioning Steps: Page 14

Wi‑Fi Connection Methods for KDHA

Option 1 – XE7C‑24/HC Wired Wall Controller (Wi‑Fi Built‑In)

✅ Most common / simplest setup
  • All KDHA ducted units are supplied with the XE7C‑24/HC wired wall controller.
  • The XE7C‑24/HC has integrated Wi‑Fi — no external Wi‑Fi module is required.
  • The controller connects directly to the EWPE (Ewpe Smart) app once Wi‑Fi is enabled and configured.
Ordering requirements
  • ✅ KDHA ducted unit
  • ✅ XE7C‑24/HC (supplied with unit)
  • ❌ No ME31‑00/C13 Wi‑Fi module required
? Reference: KDHA Owner’s Manual – Wi‑Fi Setup pages 25–26

Option 2 – LE60‑13/GH‑B Zone Control Kit (Zoned Systems)

✅ Used when zoning is required
When a KDHA system is installed with the LE60 Zone Control kit, Wi‑Fi is not built into the LE60 interface.
To enable EWPE app connectivity, an external Wi‑Fi module must be added.
Required hardware
  • ✅ LE60‑13/GH‑B Zone Control kit
  • ✅ Wired wall controller supplied with LE60 kit
  • ✅ ME31‑00/C13 Wi‑Fi module (optional additional part)
Without the ME31‑00/C13, the EWPE app will not connect.
? Reference: LE60 Zone Control Installation Manual – Wi‑Fi Module Installation, Page 11


For further guidance click on the link below

Braemar LE60 Zone Control — Installation, Commissioning & EWPE App (Wi‑Fi) Setup: Seeley International Pty Ltd 

Summary – What Do I Need?

Installation type

Wi‑Fi included

Extra parts required

KDHA with XE7C‑24/HC (no zoning)

✅ Yes

❌ None

KDHA with LE60‑13/GH‑B zoning

❌ No

✅ ME31‑00/C13 Wi‑Fi module

EWPE App – Connection Procedure (Both Methods)

The EWPE app setup process is the same regardless of whether Wi‑Fi comes from the XE7C‑24/HC controller or the ME31‑00/C13 module.

1. Install EWPE App

  • Download “Ewpe Smart” from the App Store or Google Play
  • Register or log in to an EWPE account
? Reference: KDHA Owner’s Manual – EWPE App Download

2. Reset Wi‑Fi on the Controller / Module

Ensure the unit is powered ON.
From the wired controller:
  1. Press Menu / OK
  2. Navigate to Set
  3. Select Reset Wi‑Fi
  4. Confirm reset
✅ Wi‑Fi reset is successful when:
  • "Reset Succeeded" is shown, or
  • The Wi‑Fi icon flashes every 0.5 seconds
? Reference: KDHA Owner’s Manual – Reset Wi‑Fi, Page 26

3. Add Device in EWPE App

  1. Open the EWPE app
  2. Tap Add Device / +
  3. Select Air Conditioner / Wired Controller
  4. Connect to the appliance Wi‑Fi
  5. Select the customer’s home Wi‑Fi network
  6. Enter the Wi‑Fi password
  7. Follow on‑screen prompts
⏱ Connection may take up to 2 minutes.
? Reference: LE60 Installation Manual – EWPE App Commissioning Page 14

Common Issues

✅ 2.4 GHz Wi‑Fi only (5 GHz networks will fail) ✅ Phone must stay connected to the same Wi‑Fi during setup ✅ Location permissions must be enabled on Android devices ✅ Ensure Wi‑Fi reset is performed before pairing ✅ Avoid mobile hotspot setups during commissioning

Key Takeaways

  • XE7C‑24/HC = Wi‑Fi built in → no extra parts
  • LE60 Zone Control = Wi‑Fi not built in
  • ME31‑00/C13 is mandatory for zoned Wi‑Fi EWPE control